32310-08A Grip Sensor Compatible with Harley 11-13 FLTRU Ultra

Product Name: Electronic Grip Sensor Kit Position Sensor OE Part Number: 32310-08A Product Type: Motorcycle Electronic Control Sensor Installation Location: Inside the right handlebar / Beneath the grip Control Method: -by-Wire (Electronic ) Sales Unit: 1 Kit : One Year Compatible Models: Compatible with FLHT Electra Glide Standard 2008–2009 Compatible with FLHTC Electra Glide for Classic 2008–2013 Compatible with FLHTCU Ultra for Classic Electra Glide 2008–2013 Compatible with FLHTK Electra Glide Ultra Limited 2010–2013 Compatible with FLHR Road King 2008–2013 Compatible with FLHRC Road King for Classic 2008–2013 Compatible with FLHX Street Glide 2008–2013 Compatible with FLTR Road Glide 2008–2009 Compatible with FLTRX Road Glide Custom 2010–2013 Compatible with FLTRU Road Glide Ultra 2011–2013 CVO Models: Compatible with 2008 CVO Road King FLHRSE4 Compatible with 2008 CVO Ultra for Classic FLHTCUSE3 Compatible with 2009 CVO Road Glide FLTRSE3 Compatible with 2009 CVO Ultra for Classic FLHTCUSE4 Compatible with 2010 CVO Street Glide FLHXSE Compatible with 2010 CVO Ultra for Classic FLHTCUSE5 Compatible with 2011 CVO Road Glide Ultra FLTRUSE Compatible with 2011 CVO Street Glide FLHXSE2 Compatible with 2011 CVO Ultra for Classic FLHTCUSE6 Compatible with 2012 CVO Road Glide Custom FLTRXSE Compatible with 2012 CVO Street Glide FLHXSE3 Compatible with 2012 CVO Ultra for Classic FLHTCUSE7 Compatible with 2013 CVO Road Glide Custom FLTRXSE2 Compatible with 2013 CVO Road King FLHRSE5 Compatible with 2013 CVO Ultra for Classic FLHTCUSE8 Kit Contents: 1× Electronic Grip Sensor Assembly Long wiring harness with pre-crimped metal terminals 6-pin black main connector Grey waterproof connector with orange seal Terminals and terminal locks Green connector locking tab Black insulation/heat-shrink protective sleeve Common Symptoms of Failure: Check Engine Light (CEL) illuminated No response or sluggish response Erratic output (fluctuating levels) Vehicle enters power-limited mode Engine forced into idle mode Intermittent faults occurring after handlebar replacement or internal wiring routing Common Fault Codes: P1270: TGS Dual-Channel Verification Fault P2122: TGS 1 Signal Low or Open Circuit P2123: TGS 1 Signal High P2127: TGS 2 Signal Low or Open Circuit P2128: TGS 2 Signal High P2138: TGS 1/2 Signal Correlation Error P1510: Limited Mode P1511: Power Management Mode P1512: Forced Idle Mode Installation Notes: Disconnect the negative terminal before installation Route the wiring harness through the interior of the right handlebar Insert the six terminals into the main connector after routing the wires Install strictly according to pin positions 1–6 to avoid reversing the two circuit groups Do not pull, sharply bend, kink, or pinch the wiring harness the terminals from being scratched by the edges of the handlebar holes Check circuit continuity after installation Ensure the harness is not pulled taut when the handlebars are turned fully to the left or right The must return smoothly and automatically after being released Perform the electronic learning or calibration procedure after clearing fault codes Refer to the specific vehicle service manual or sensor supplier instructions for the exact procedure Professional installation by an experienced motorcycle technician is recommended Friendly Reminder: Please verify the vehicle year, model, engine configuration, and part number before If you are unsure about compatibility, please us for assistance

Compatibility:Designed for selected 2008–2013 FLHT FLHR FLHX FLTR and CVO series motorcycles using reference 32310-08A

Signal function:Transmits grip position signals to the electronic control system for responsive operation

Handlebar design:Features a long wiring harness for internal routing through the right handlebar beneath the grip

Kit contents:Includes grip sensor assembly, connectors, terminals, locking pieces and protective sleeve

Installation note:Verify the part number, connector layout and terminal positions 1–6 before installation by a qualified technician